Support

Articles in this section

How to Replace, Add, or Remove a Transmitter

Please use the instructions below to replace, add or remove a TireMinder Transmitter.

Information on how to replace, add, or remove transmitter for the TireMinder Smart TPMS App can be found here: How to Replace, Add, or Remove a Transmitter On The TireMinder Smart TPMS

How to Replace a Transmitter

  1. Remove the transmitter you are replacing from the valve stem.
  2. While in Monitoring Mode, press and hold the left and right buttons until you see all 22 tire positions.
  3. Press and release the right button and navigate to the position you wish to replace. Once at this position, the light on the top of the monitor should be green and you should have a pressure reading.
  4. Press and hold the center button for 5 seconds. After 5 seconds, you will see the green light turn red and "--- PSI" will be displayed.
  5. Attach your new transmitter to the valve stem. Within 5 to 15 seconds you will see a pressure reading and a green light on the top of the monitor.
  6. Press and hold the left and right buttons for 5 seconds until the 22 tire positions disappear and you are left with only the previously programmed tire positions.

How to Add a Transmitter

  1. Make sure you are in Monitoring Mode. Monitoring Mode is the mode where you can switch between temperature and pressure using the right and left button.
  2. Press and hold the left and right buttons for 5 seconds until you hear a beep and see all 22 tire positions on the monitor.
  3. Once you see all 22 tire positions, you can confirm you are in Learning Mode. This mode is where you can add or remove a tire position.
  4. Using the left, right and center buttons, set each tires baseline to the desired pressure.
  5. To add a transmitter, go to the desired tire position on the monitor that correlates to the physical position you would like to monitor, example: position #1 on the display and the front driver’s side tire of a Motorhome.
  6. Once you are at the position you would like to add on the monitor, attach the transmitter to the valve stem.
  7. After about 5-30 seconds the monitor will receive a reading from the transmitter and display it on the monitor. It will also shine a green light on the top of the monitor.
  8. Use the right and left buttons to move from tire to tire to add each transmitter to your vehicle(s).
  9. Once all desired transmitters have been added to the correct location, you can exit Learning Mode by pressing and holding the left and right buttons for 5 seconds until you hear a beep.
  10. You will now be back in Monitoring Mode. Make sure the amount of tires you have added are the same amount being displayed in Monitoring Mode. (Example: If you added 10 transmitters, make sure Monitoring Mode displays 10 tire positions).

Note: In Learning Mode, a red light on the top means no transmitters have been learned to this position. A green light, on the other hand, means a transmitter has been learned to this position.

Note: In Learning Mode, once a transmitter has been learned to a position, that transmitter cannot be learning to another position. If you are having trouble learning a transmitter to a position, make sure the transmitter has not accidentally be learned to a previous position.

How to Remove a Transmitter

  1. Make sure you are in Monitoring Mode. Monitoring Mode is the mode where you can switch between temperature and pressure using the right and left button.
  2. Press and hold the left and right buttons for 5 seconds until you hear a beep and see all 22 tire positions on the monitor.
  3. Once you see all 22 tire positions, you can confirm you are in Learning Mode. This mode is where you can add or remove a tire position.
  4. Using the right or left buttons, move to the position you wish to remove/unlearn from the monitor. Once you are on the position, press and hold the center button for 5 seconds until you hear a beep.
  5. Once you hear the beep, the monitor will show 3 dashes and the light on the top would have gone from green to red, confirming the removal of the transmitter.
  6. Once all desired transmitters have been removed, you can exit Learning Mode by pressing and holding the left and right buttons for 5 seconds until you hear a beep.
  7. You will now be back in Monitoring Mode. Make sure the amount of tires you have removed are the same amount being displayed in Monitoring Mode. (Example: If you removed 10 transmitters from a total of 12 Transmitter, make sure Monitoring Mode displays only 2 tire positions.)

Note: If you are doing a complete uninstall or starting over, slowly go through each position in Learning Mode, starting with the first position and make sure each position displays three dashes and a red light on the top of the monitor. If the position shows a green light, remove the position using the previous instructions.